The FreeBSD Diary

Being so used to "plain sailing" installations, I had no idea how I was going to grace my new toy with my OS of choice, so I raced to http://www.FreeBSD.org to gather information on alterative methods.  I tried an installation from a DOS partition, which the notebook refused to play along to.  I have no network card (yet), so an FTP installation was out of the question.  This only left one other option - PLIP.

For those that are unaware of what PLIP is, or what it does, PLIP is a rather clever way of utilising a parallel port as a pseudo ethernet interface.  I must admit, the whole process looked rather daunting from the outset, but it was actually rather simple. For this reason, I've decided to submit this article to the FreeBSD Diary [Editor's note: with my thanks].

A year or so ago (before I built up my LAN), I invested in a null modem (aka laplink) cable to share files between my home PC, and the machine I often borrowed from work.   If you are to follow the instructions in this article, you will need one yourself.   If you do not have one, or you cannot buy one, they are relatively simple to make yourself, but the schematics are beyond the scope of this article.  A quick visit to a search engine should do you some justice.

In order for this installation to work, you must also have another machine running FreeBSD (there are a few other operating systems that provide a compatible PLIP system, Linux being one of them - but dont forget to read 'man plip' first, since Linux uses a slightly different method).  Adding PLIP to your kernel is as easy as adding the line:

device plip0 at ppbus?

to your kernel configuration, recompiling your kernel, installing it and rebooting.   If you do not already have parallel support in your kernel, then you must add it.

Please be aware, that PLIP has a greater priority than other parallel activity, and other devices that exist on your parallel port will not work while the PLIP interface is up.

After your kernel is prepared, you will need to set up the interface on the machine that is to provide it's gateway - that is, the machine with FreeBSD already installed on it.  You will notice (with a quick ifconfig -a) that you have a new interface - lp0. Because lp0 is just like any interface, you may set it up in a very similar way (with only one major difference).  Let's start by giving it an IP address:

ifconfig lp0 inet 192.168.0.1 netmask 0xffffff00 192.168.0.2

Notice the extra argument at the end of this statement. PLIP needs to know what the IP address at the other side of the link is (will be). Note that if you would like lp0 to be configured permanently, you may add it to rc.conf in exactly the same way as other interfaces, with one small change. Here is an extract from my rc.conf to illustrate:

interfaces="lo0 xl0 lp0"
ifconfig_xl0="inet 10.0.0.1 netmask 0xffff0000"
ifconfig_lp0="inet 192.168.0.1 192.168.0.2 netmask 0xffffff00"

Notice again the extra argument specifying the IP address at the other side of the link.

Once you have one side of the link set up, it is time (after plugging in the cable) to start the process of installation.  This article assumes that you already know how to perform an FTP install [Ed. note: Installing FreeBSD to replace Windows actually does an FTP install, so that might help], as there is only one more step to take that is different from a normal process.

Slap in your boot disk, select your options, and get yourself up to the point of choosing your installation method.  Choose FTP install, and you should be prompted to set up your network interface. Choose lp0, and enter the appropriate details, entering the IP address for *this* end of the link (in my scenario, this is 192.168.0.2).   The only difference now from a normal FTP install, is that in the box entitled "Extra options to ifconfig", you must enter the IP address of the machine at the other end of the link - in this case, 192.168.0.1

As long as your lp0 interface has access to the outside world, there is nothing more to do, except grab a coffee and relish in the fact that yet another box is about to bathe in the glory that is FreeBSD.

Enjoy.